Correct way to load steel coils
Release time:
2024-07-29
Horizontal loading: When the ratio of the width to the diameter of the steel coil is greater than 0.7, horizontal loading should be selected. Horizontal loading is divided into transverse loading and longitudinal loading. The specific method to be selected depends on the size of the steel coil and the transportation conditions.
There are two main ways to correctly load steel coils: vertical loading and horizontal loading.
Vertical loading: When the ratio of the width to the diameter of the steel coil is less than or equal to 0.7, the vertical loading method should be selected, and the axis of the steel coil hole is perpendicular to the loading plane. This loading method is suitable for small steel coils and can effectively prevent them from rolling during transportation.
Horizontal loading: When the ratio of the width to the diameter of the steel coil is greater than 0.7, the horizontal loading method should be selected. Horizontal loading is divided into horizontal loading and longitudinal loading. The specific method to be selected depends on the size of the steel coil and the transportation conditions. The following points should be noted when loading steel coils: Use fixed seats and wave racks: Fixed seats and wave racks should meet the safety requirements of transportation. It is recommended to use #16 channel steel and 8mm steel plates. Rubber sheets should be padded at the bottom and tied with bolting devices.
Use sleepers and triangular wood: Lay wooden boards or anti-slip grass mats at the bottom of the cargo compartment to increase friction and reduce the possibility of sliding. Sufficient pads should be used between any two steel coils, and some triangular wood should be prepared before leaving the vehicle in case of emergency.
Reasonable tying: After loading, tighten the wire rope with a hand-cranked hoist to ensure that each steel coil is firmly fixed.
Practical suggestions and tips:
Choose the appropriate loading method: Choose the appropriate loading method according to the size and weight of the steel coil to ensure safety and efficiency.
Use special brackets and containers: For large or heavy steel coils, using special brackets or containers can better fix and protect the steel coils.
Through the above methods, the safety and stability of the steel coils during transportation can be effectively ensured.
RELATED NEWS
The difference between steel coil and steel strip
The main differences between steel coils and steel strips are the width, purpose and processing methods. Steel coils are suitable for large-scale storage and transportation, as well as for a variety of subsequent processing, while steel strips are more suitable for the production of narrow and long steel plates to meet specific industrial needs.
2024-03-21
Which is stronger, galvanized pipe or stainless steel pipe?
Stainless steel pipes are not easy to rust, easy to clean, and have a long service life; although galvanized pipes also have certain anti-corrosion properties, the zinc layer will corrode over time, affecting its firmness.
2024-02-10
Correct way to load steel coils
Horizontal loading: When the ratio of the width to the diameter of the steel coil is greater than 0.7, horizontal loading should be selected. Horizontal loading is divided into transverse loading and longitudinal loading. The specific method to be selected depends on the size of the steel coil and the transportation conditions.
2024-07-29
Why steel and concrete work together
Economical: Taking advantage of the high compressive strength of concrete and the strong tensile strength of steel bars, materials can be used reasonably and costs can be saved.
2024-06-28
In the medical field, surgical plates and medical steel plates usually use materials such as stainless steel or titanium alloys, which have good biocompatibility and corrosion resistance and are suitable for implants in the human body. Although these surgical materials may contain iron elements, they are specially designed and processed alloys to meet specific medical requirements, rather than simple iron products.
2024-04-18
The hardness of steel bars is one of the important indicators to measure their quality and is crucial to the stability and safety of building structures. With appropriate hardness testing methods, the hardness of steel bars can be evaluated to ensure their safe use in engineering.
2023-03-14
CONTACT US
Address : Address: Xijin Times Center Square, Huaiyin District, Jinan City, Shandong Province
Copyright : Yegang Iron and Steel (Shandong) Group Co., LTD Powerby : 300.cn jinan2 SEO Business license Privacy Policy
